Hi,
I installed a particulate egg yesterday and connected without problems, but when I tried to register it I got the "egg not found" message, even after I let it run overnight.
So today I brought it in to redo the connection process, it went fine, except again I got the "egg not found" message". I installed it outside, making sure it connected to my wifi network and showed data. Now, even after more than an hour I still get the same message.
I copied the text of the installation process and will paste it after my text, erasing the serial number in the text.
Maybe somebody can help me with this issue, I've only a very basic knowledge of how to connect devices to wifi networks.
Thanks!
Here is the text:
------------------------------------+
| Welcome to Air Quality Egg 2.0 |
| Particulate Sensor Suite |
| Firmware Version 2.1.8 |
+------------------------------------+
Compiled on: May 2 2016 12:17:01
Egg Serial Number: egg008028************
Info: Tiny Watchdog Initialization...OK.
Info: Slot Select Pins Initialization...OK.
Info: SPI Flash Initialization...OK.
Info: SD Card Initialization...Fail.
Info: Current firmware signature: 318054 56780
Info: SHT25 Initialization...OK.
Info: RTC Initialization...Fail.
Info: ESP8266 Initialization...OK.
Enter 'aqe' for CONFIG mode.
OPERATIONAL mode automatically begins after 12 secs of no input.
11...10...9...
aqe
-~=* In CONFIG Mode *=~-
OPERATIONAL mode begins automatically after 5 mins without input.
Enter 'help' for a list of available commands,
...or 'help ' for help on a specific command
get settings
+-------------------------------------------------------------+
| Preferences/Options: |
+-------------------------------------------------------------+
Operational Mode: Normal
Temperature Units: Celsius
Altitude: Not set
Backlight Settings: 60 seconds, ON at startup
Sensor Sampling Interval: 5 seconds
Sensor Averaging Interval: 30 seconds
Sensor Reporting Interval: 5 seconds
+-------------------------------------------------------------+
| Network Settings: |
+-------------------------------------------------------------+
MAC Address: 5C:CF:7F:8B:39:9E
Method: Direct Connect
SSID: MAISON
Security Mode: Open
IP Mode: Configured for DHCP
Update Server: update.wickeddevice.com
Update Filename: aqev2_pm_esp
NTP Server: Disabled
NTP TZ Offset: 0.000000000
+-------------------------------------------------------------+
| MQTT Settings: |
+-------------------------------------------------------------+
MQTT Server: mqtt.opensensors.io
MQTT Port: 1883
MQTT Client ID: egg008028*************
MQTT Authentication: Enabled
MQTT Username: wickeddevice
MQTT Topic Prefix: /orgs/wd/aqe/
MQTT Topic Suffix: Enabled
+-------------------------------------------------------------+
| Credentials: |
+-------------------------------------------------------------+
MQTT Password backed up? [* means no]
Private key backed up? [* means no]
+-------------------------------------------------------------+
| Sensor Calibrations: |
+-------------------------------------------------------------+
PM Offset [V]: 0.884894371
PM Baseline Voltage Characterization:
idx temp [degC] slope [V/degC] intercept [V]
No valid entries found.
Temperature Reporting Offset [degC]: 4.90
Humidity Reporting Offset [%]: -12.50 +-------------------------------------------------------------+
| note: '*' next to label means the setting is not backed up. |
| run 'backup all' when you are satisfied |
+-------------------------------------------------------------+
AQE>:
@=============================================================@
# GETTING STARTED #
#-------------------------------------------------------------#
# First type 'ssid your_ssid_here' and & press #
# Then type 'pwd your_network_password' & press #
# Then type 'get settings' & press to review config #
# Finally, type 'exit' to go into OPERATIONAL mode, #
# and verify that the Egg connects to your network! #
@=============================================================@
AQE>:
AQE>: ssid MAI*****
AQE>:
AQE>: pwd Canada****
AQE>:
AQE>: get settings
+-------------------------------------------------------------+
| Preferences/Options: |
+-------------------------------------------------------------+
Operational Mode: Normal
Temperature Units: Celsius
Altitude: Not set
Backlight Settings: 60 seconds, ON at startup
Sensor Sampling Interval: 5 seconds
Sensor Averaging Interval: 30 seconds
Sensor Reporting Interval: 5 seconds
+-------------------------------------------------------------+
| Network Settings: |
+-------------------------------------------------------------+
MAC Address: 5C:CF:7F:8B:39:9E
Method: Direct Connect
SSID: MAISON
Security Mode: Open
IP Mode: Configured for DHCP
Update Server: update.wickeddevice.com
Update Filename: aqev2_pm_esp
NTP Server: Disabled
NTP TZ Offset: 0.000000000
+-------------------------------------------------------------+
| MQTT Settings: |
+-------------------------------------------------------------+
MQTT Server: mqtt.opensensors.io
MQTT Port: 1883
MQTT Client ID: egg008028****************
MQTT Authentication: Enabled
MQTT Username: wickeddevice
MQTT Topic Prefix: /orgs/wd/aqe/
MQTT Topic Suffix: Enabled
+-------------------------------------------------------------+
| Credentials: |
+-------------------------------------------------------------+
MQTT Password backed up? [* means no]
Private key backed up? [* means no]
+-------------------------------------------------------------+
| Sensor Calibrations: |
+-------------------------------------------------------------+
PM Offset [V]: 0.884894371
PM Baseline Voltage Characterization:
idx temp [degC] slope [V/degC] intercept [V]
No valid entries found.
Temperature Reporting Offset [degC]: 4.90
Humidity Reporting Offset [%]: -12.50 +-------------------------------------------------------------+
| note: '*' next to label means the setting is not backed up. |
| run 'backup all' when you are satisfied |
+-------------------------------------------------------------+
AQE>:
AQE>: exit
Exiting CONFIG mode...
-~=* In OPERATIONAL Mode *=~-
Info: Beginning Network Scan...
Info: Network Scan found 0 networks
Info: Found Access Point "MAISON", Not Found.
Info: Connecting to Access Point with SSID "MAISON"...OK.
Info: Request DHCP...OK.
Info: IP Addr: 192.168.2.15
Info: Netmask: 255.255.255.0
Info: Gateway: 192.168.2.1
Info: Mirrored configuration already matches current configuration.
Info: Resolved "update.wickeddevice.com" to IP address 45.55.159.249
Info: -------------------------------------
Info: Integrity Checks:
Info: File Size: 318054
Info: CRC16 Checksum: 56780
Info: Download Complete
Info: Total Bytes: 212
Info: File Size: 12
Info: Checksum: 45818
Info: Duration: 5232
Info: Signature matches, skipping HEX download.
Info: Resolved "mqtt.opensensors.io" to IP address 54.77.197.239
Info: Connecting to MQTT Broker with Client ID "egg008028**********" using Authentication...OK.
csv: Timestamp,Temperature[degC],Humidity[percent],PM[ug/m^3],PM[V],Latitude[deg],Longitude[deg],Altitude[m],
csv: 01/01/1970 00:02:05,---,---,---,---,---,---,---
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat/egg008028bfe7080152...OK.
csv: 01/01/1970 00:02:10,---,---,---,---,---,---,---
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat/egg008028bfe7080152...OK.
csv: 01/01/1970 00:02:15,---,---,---,---,---,---,---
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat/egg008028bfe7080152...OK.