Hi all,
I recently purchased an Air Quality Egg 2. I have followed the instructions as given (i.e. using the serial console, defining the wireless SSID and password before exiting, unplugging from the computer and plug into a mains-USB adapter).
I can ping the device so I am know the egg is connected to the network. However, when I then try to add my egg from http://airquality egg.com using the serial ID given in my user manual (i.e. something like egg1234567890123456), the web page returns 'egg not found'.
I have noticed I am getting an error message in the console output which I have added below. Here is the output (note the error message 'Error: Couldn't resolve 'update.wickeddevice.com'). (note I have changed the serial ID displayed in the output just in case this needs to be kept private).
Any ideas would be much appreciated. For example, do I need to change any settings on my router (e.g. port forwarding)? Do I need to update my firmware? Is there a known bug inhibiting the new AQE devices to register with the 'cloud'?
Thanks
Robbie
CONSOLE OUTPUT:
Serial Monitor:
Port: Speed: Disconnect
Warning! Because of a known bug on Chrome, you should press the disconnect button before physically disconnecting your device.
Or else the connection with the serial monitor will stay open until you restart your browser.
+------------------------------------+
| Welcome to Air Quality Egg 2.0 |
| NO2 / CO Sensor Suite |
| Firmware Version 2.0.4 |
+------------------------------------+
Compiled on: Aug 24 2015 12:47:06
Egg Serial Number: egg1234567890123456
Info: Tiny Watchdog Initialization...OK.
Info: Slot Select Pins Initialization...OK.
Info: SPI Flash Initialization...OK.
Info: SD Card Initialization...Fail.
Info: Current firmware signature: 346044 18705
Info: SHT25 Initialization...OK.
Info: NO2 Sensor AFE Initialization...OK.
Info: NO2 Sensor ADC Initialization...OK.
Info: CO Sensor AFE Initialization...OK.
Info: CO Sensor ADC Initialization...OK.
Info: RTC Initialization...Fail.
Info: CC3000 Initialization...OK.
Enter 'aqe' for CONFIG mode.
OPERATIONAL mode automatically begins after 12 secs of no input.
11...10...9...8...7...6...5...4...3...2...1...0...
-~=* In OPERATIONAL Mode *=~-
Info: Beginning Network Scan...
Info: Network Scan found 8 networks
Info: Found Access Point "scoobydo", RSSI = 83
Info: Connecting to Access Point with SSID "scoobydo"...OK.
Info: Request DHCP...OK.
Info: IP Addr: 192.168.1.115
Info: Netmask: 255.255.255.0
Info: Gateway: 192.168.1.1
Info: DHCPsrv: 192.168.1.1
Info: DNSserv: 192.168.1.1
Info: Mirrored configuration already matches current configuration.
Error: Couldn't resolve 'update.wickeddevice.com'
Info: Resolved "opensensors.io" to IP address 52.19.195.193
Info: Connecting to MQTT Broker with Client ID "egg1234567890123456" using Authentication...OK.
Info: Sampling Sensors @ 70685
csv: Timestamp,Temperature[degC],Humidity[percent],NO2[ppb],CO[ppm],NO2[V],CO[V]
csv: 01/01/1970 00:01:11,---,---,---,---,0.000000,0.000000
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat...OK.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Sampling Sensors @ 75685
csv: 01/01/1970 00:01:16,---,---,---,---,0.000000,0.000000
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat...OK.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Sampling Sensors @ 80685
csv: 01/01/1970 00:01:21,---,---,---,---,0.000000,0.000000
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat...OK.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Sampling Sensors @ 85693
csv: 01/01/1970 00:01:26,---,---,---,---,0.000000,0.000000
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat...OK.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Sampling Sensors @ 90693
csv: 01/01/1970 00:01:31,---,---,---,---,0.000000,0.000000
Info: MQTT publishing to topic /orgs/wd/aqe/heartbeat...OK.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.
Info: Watchdog Pet.