CO2 AQE v2 Reporting Constant Nonzero Value
Not that I'm aware of, but the sensor is in a remote location at the moment so I can't say for certain. It was moved to another location around noon today.
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
Gotcha, I can't entirely rule out a software problem, but I generally agree with your intuition given that it was working fine for a long period of time and then started experiencing a behavioral...
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
Is there some way I can test the sensor? Or open the egg up and install a replacement sensor? I'd like to try to troubleshoot a bit before going here though..
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
The only way I can think to test the sensor, per se, would be to load an test program onto the Egg using Arduino, and I don't have one handy to point you to at the moment unfortunately. I would advise...
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
I can do that too, just let me know how best to proceed.
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
We are closed next week, but yea I would say if it doesn't self correct, your best bet would be to send it back to us for evaluation and repairs as needed. If we need to replace the CO2 sensor, I...
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
Sure, that works. Any documentation or reference numbers I need to send along with it?
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
Good point, I'll private message you a RMA #.
View ArticleTurner Onner - Can't connect to IP address
Hello, My son is creating the Turner Onner for a homeschooling project. He got all the way to the end, was given an IP address, but can't connect to it in any browser. What do we do from here? He...
View ArticleTurner Onner - Can't connect to IP address
If he got all the way to obtaining an IP address he should be home free... is the computer he's using a browser to connect with on the same network as the NodeMCU connected to? That's required for it...
View ArticleTurner Onner - Can't connect to IP address
Yes, we can get an IP address, but then can't connect to the server. The device and browser are on the same wifi network. Any other suggestions?
View ArticleTurner Onner - Can't connect to IP address
Hm... I haven't seen that happen before. @Dirk might have some other ideas? One other thing I would have you check is whether you can "ping" the NodeMCU by its IP address. This is done using a command...
View ArticleTurner Onner - Can't connect to IP address
Okay, we were trying to do this on my son's Windows laptop. We just tried it on my Mac and have a new problem. When trying to upload the code, we got the following errors: Arduino: 1.8.1 (Mac OS X),...
View ArticleTurner Onner - Can't connect to IP address
Also, the IP address we were given on the laptop setup was not 192.168.1.23. Is that okay?
View ArticleTurner Onner - Can't connect to IP address
On a Mac, I believe you need to install a USB driver as per https://github.com/nodemcu/nodemcu-devkit/wiki/Getting-Started-on-OSX
View ArticleTurner Onner - Can't connect to IP address
That IP address was just representative, not literal
View ArticleClik here to view.
Turner Onner - Can't connect to IP address
I gave up on trying it with the Mac. Once again, I am able to connect on my Dell laptop, and I get an IP address in the serial monitor. When I type that address into a web browser, I get "Unable to...
View ArticleClik here to view.
Turner Onner - Can't connect to IP address
Here is the serial monitor: image.png1366x768 70.8 KB
View ArticleSoft circuits pdf page not found
Make: Wearable by Dirk Swart claims that a pdf is to be found on Wicked Device at http://shop.wickeddevice.com/wp-content/uploads/2016/05/softcircuits.pdf. But "no page found" comes up. Can anyone...
View Article