4 SO2, o3 eggs. One working. URGENT
Dirk, any progress with this? I sent you a data file, and no response in a few days. At the moment, I have three eggs in my office, reading ozone values of 80+ppb, 0.0ppb, 9.7ppb, and one in a...
View Article4 SO2, o3 eggs. One working. URGENT
Hi Liz. My apologies for the slower than usual reply. I'm on the road right now, which causes me to lag. Please can you review the documents here for information about the variation of the sensors....
View ArticleAQEv2 problem initialising
Worked when I restored everithing, but when running the latest code form http://github.com/wickeddevice/aqev2fw_no2co_esp (even without any modifications) I get the "?" instead of reading. I think...
View ArticleAQEv2 problem initialising
@aarepuu it's not outside the realm of possibility that the latest on Git-Hub may have some undiscovered problem. Let me know if you find something wrong. Could be that you've got the wrong board...
View Article4 SO2, o3 eggs. One working. URGENT
Hi Dirk. I looked through the documents. It appears I'll have to recalibrate the eggs, getting new bias and slope for voltage to ppb conversion. If you have any information on this please send on....
View Article4 SO2, o3 eggs. One working. URGENT
Dirk -can you point me towards information on calibrating o3/so2 sensors? Thanks
View Article4 SO2, o3 eggs. One working. URGENT
Let me check that I understand what you are asking, as this is quite a large topic. There is a temperature dependent zero calibration and a temperature INdependent sensitivity, and also a sample...
View ArticleAQE dashboard visualizer apparently stopped
It seems the process for https://airqualityegg.wickeddevice.com/dashboard/#/egg/egg0*************** is now frozen and needs restart. Devices live at OS but above url seems stuck.Speaking of OS, I have...
View ArticleWildfire V3 any help please
So. Codebender is no more. and there does not seem to be any board support for wildfire in the Arduino IDE. is it possible to use a wildfire v3 at this point? (Note. this was a new purchase I made...
View ArticleClik here to view.
Wildfire V3 any help please
Hi @Marvin_Francois_Fath, it's a tragedy about Code Bender .There actually is a board support package for Arduino IDE that should work fine though. The Boards Manager URL is:...
View ArticleWildfire V3 any help please
Hi I just purchased a wildfire v3 from Microcenter but I cannot seem to get the ip address of the unit when I boot it. I used putty and the TI app but I do not see the message Welcome to Widlfire"...
View ArticleWildfire V3 any help please
Hi @rjvtech2, FYI the most recent (and currently supported) version of WildFire is v4, which uses an ESP8266 module rather than a CC3000 module (which Texas Instruments has discontinued). At any rate,...
View ArticleAQE v2 won't initialize: sends invalid HTTP packet to update server
Hey, Earlier in the year Engage Liverpool CIC bought five air quality eggs (v2) which they didn't have a lot of luck with (for various reasons). I don't know a lot about their history but I've...
View ArticleClik here to view.
AQE v2 Config Integrity Check Failed
One of the five air quality eggs I've recently taken over had been flashed with the Arduino "blink" test program in an attempt to bring it back to life. I followed the instructions on Reprogramming an...
View ArticleAQE v2 won't initialize: sends invalid HTTP packet to update server
Hi Paul, thanks for contacting us, I see these are running 2.0.x firmware, which implies they are using the CC3000 chipset for Wi-Fi which TI has stopped supporting, and we've since switched to using...
View ArticleAQE v2 Config Integrity Check Failed
I suspect something has probably changed in the current version of Arduino causing the compile errors you are experiencing. I probably just wants a forward declaration now for some reason that wasn't...
View ArticleAQE v2 won't initialize: sends invalid HTTP packet to update server
Thanks Victor - that sounds good. I'm going to round up the 5th egg first then look at sending them all your way. I'll send you an email. CheersPaul
View ArticleClik here to view.
CO2 AQE v2 Reporting Constant Nonzero Value
I've got a CO2 egg that has worked great for ~2 months now, but the past few days it has been broadcasting a constant nonzero value. Any thoughts? Image below shows the sensor flat line at ~830 ppm....
View ArticleCO2 AQE v2 Reporting Constant Nonzero Value
Hi @NT1, interesting, was there anything contextually noteworthy surrounding this change in behavior? I just downloaded the last 5 hours of data. and it's not entirely flat-lining, there was some kind...
View Article