AQEv2 problem initialising
Hi! Did you manage to fix this issue? I also did a firmware update according to the same link - http://shop.wickeddevice.com/2015/08/26/re-programming-an-air-quality-egg-v2/. Now it's stuck on...
View ArticleTurning off the AQE version 2 lights?
Is there any way or command to turn off the lights that flash when data is uploaded etc? There's a green and a red light that flash sporadically - presumably on upload and other events? If this is a...
View ArticleAQEv2 problem initialising
@aarepuu I'm going to recommend that you email us at support at wicked device dot com so that we can arrange to replace your Wi-Fi board. We are using a new generation of Wi-Fi chipset now, and we can...
View ArticleTurning off the AQE version 2 lights?
Hi @mking007 not much I can do about the LEDs, short of not populating or depopulating them on request (which we are happy to do). It is possible to make it so that the backlight never turns on...
View ArticleClik here to view.
AQEv2 problem initialising
Thank you for the quick response! I have multiple eggs which all have the same hardware, then I would need to replace the Wi-Fi board on all of them. I was also looking for the old firmware for my...
View Article4 SO2, o3 eggs. One working. URGENT
Hi, we've just got four so2-o3 eggs, ordered 9th Sept. They are hooked up, publishing to opensensors: egg nos.: egg008012a84a8880130, egg00802a54700b0123, egg0080287351180112, egg00802a84a90a0130....
View ArticleAQEv2 problem initialising
@aarepuu Multiple eggs is no problem for us, I'd like to get you up to the latest hardware if possible. Please go ahead and email support so we can work out details. Incidentally, the way I've been...
View ArticleAQEv2 problem initialising
Hi Vic, I put the firmware from http://github.com/wickeddevice/aqev2fw_no2co_esp onto the egg and it worked fine. I think I have the newest chip in there, I was just using the old firmware code. If...
View ArticleAQEv2 problem initialising
@aarepuu cool, no problem, keep in mind that there are different firmwares for different Egg sensor payload models (e.g. Model B, Model C, Model D, model E), and 2.0.x and 2.1.x are not compatible as...
View ArticleAQEv2 problem initialising
Thanks! I was looking for the aqev2fw_no2co_esp firmware one, but couldn't find it before for some reason. Thanks for clearing this up!
View Article4 SO2, o3 eggs. One working. URGENT
It appears that your eggs are working fine. Here's a short narrative of the steps that you can go through to determine that in case you ever need to sleuth this down in the future. Egg data can be...
View Article4 SO2, o3 eggs. One working. URGENT
Not really, dirk. One egg is measuring 40ish ppb , other three, zero. All four giving so2. Would warm up time exceed 5hours or so? If so, why( just out of interste). Ive already succeasfully grabbd...
View Article4 SO2, o3 eggs. One working. URGENT
Can you share the data downloads you have via email? I just pulled the data again from the eggs 2 minutes ago and I'm just not seeing anything consistent with 'other three, zero'. Can you share your...
View ArticleAQE firmware update
I've got an AQE v2 which says it has 2.1.8 firmware when it boots up. I have 2 other AQE v2s which were bought later and they both have firmware 2.1.9 Should the other egg upgrade its firmware to...
View ArticleAQE firmware update
@mking007 The official baseline right now is 2.1.8. We've started shipping some Eggs with 2.1.9 release candidate software and will push an official 2.1.9 update probably within the next month. Eggs...
View ArticleClik here to view.
AQE firmware update
Thanks for the clarification @vicatcu FWIW that feature would be great, but I'd ask for it to be a toggle on-off feature as there are definitely times when offline mode should be using less power and...
View ArticleAQEv2 problem initialising
Hi!After flashing the new firmware from http://github.com/wickeddevice/aqev2fw_no2co_esp, I can't get any readings to display on the egg. It just displays:TEMP ? RH ? NO2 ? CO ? When I look at the...
View ArticleAQEv2 problem initialising
Actually when I look at the file it shows: 11/17/2016 17:44:47,?,?,?,?,?,?,---,---,---11/17/2016 17:44:52,?,?,?,?,?,?,---,---,---11/17/2016 17:44:57,?,?,?,?,?,?,---,---,---11/17/2016...
View ArticleAQEv2 problem initialising
@aarepuu That is pretty weird. Are you still trying to run a customized software load? Here's what I would recommend to get yourself back into a factory default configuration. get into config mode to...
View Article