Angular Clock bug at 56 minutes past the hour
@ambanmba could you perhaps go through the calibration procedure again and post back the Serial Monitor output during that process?
View ArticleAngular Clock bug at 56 minutes past the hour
Wicked Device Angular Clock V1.0 Type any key and to enter meter adjustment mode Adjust Hours meter to 1 oclock position using knob on rear of clocktype spacebar when setOffset for 1 oclock is 0...
View ArticleAngular Clock Meters Don't Respond
Just finished assembling my Angular Clock. Boot procedure begins as expected, LED's flash. I can connect using Arduino Serial Monitor, BAUD set to 115,200, I receive the opening message, type any key...
View ArticleClik here to view.
Angular Clock Meters Don't Respond
Sorry to hear you're having trouble! The meters do have a polarity. Just to make sure, are the instructions you are following at http://shop.wickeddevice.com/angular-clock/? There are photographic...
View ArticleAngular Clock bug at 56 minutes past the hour
@ambanmba anything new from you on this topic? Sorry for the long delay on my end. I've been studying to code and chatting with the original author off and on. I think it's the offsets basically...
View ArticleAngular Clock bug at 56 minutes past the hour
Nothing new from me, I've been flat out with other things. I'd imagine a quick fix would be to just do a min(value, calibrated value) which would at least leave it at the high mark of the gauge. The...
View ArticleMotor Shield not Working
I have no idea why the motor shield would not work as it was working earlier. The LED is lighting up. Is it broken?EDIT: I'm sorry, it was fine.
View ArticleAdd sensors to motor shield
Hi, I have the MAKE: Motor shield, and I'd like to implement a pair of ultrasonic sensors that use a Digital Input, VCC, and GND pins, I was wondering how i'd be able to access the arduino's 5v and...
View ArticleClik here to view.
Add sensors to motor shield
If you're not using the current-sense feedback circuitry, by far the easiest place to "tap into" the Arduino with the motor shield attached is on the 2x9 header shown below. You could, for instance,...
View ArticleMotor-6 shield as a cnc controller?
Is the wicked device motor-6 h-bridge? I was wondering if i could use it as part of a cnc build and if its compatible with GRBL or any other cnc app? Also if i use unipolar 6 wire stepper motors where...
View ArticleMotor-6 shield as a cnc controller?
The Wicked Device Motor Shield has 6 independent H-Bridge ICs on it, each capable of delivering up to 1.2A Average / 3A Peak Current, and with Motor Voltage up to 15VDC. It's suitability to a...
View ArticleMotor-6 shield as a cnc controller?
I appreciate the help vicatcu. can anyone please help me with an answer than doesn't require an engineering degree. lol. I'm just a simple hobbyist. just wanted to know if my shield i bought will work...
View ArticleClik here to view.
Motor-6 shield as a cnc controller?
Haha, my bad... I'm not really that familiar with GRBL, and I'm not sure how simple of an answer I can give practically. It looks really cool and well written. But Looking at their source code on...
View ArticleMounting Air Quality Egg
Hey Everyone, I am interested in installing the Air Quality Egg outside schools. However it needs to be in a location which is representative of the people on whoms behalf it is measuring. i.e. at...
View ArticleMounting Air Quality Egg
Hi @blaise, that is great to hear, we've always believed schools are a great place for Air Quality Eggs to live for a lot of reasons! The power interface to the Air Quality Egg is a male Type A USB...
View ArticleMotor shield for R/C Omnibot
hi Wicked Device! I had a question about the Omnibot - from trawling around the site I see you sell a complete kit but I started out having a go at building it from my back-issue of Make magazine. The...
View ArticleMotor shield for R/C Omnibot
Our motor shield works for this application, as does the Make v1.1 motor shield. Are you referring to the Adafruit V2 shield when you say motor shield v2? I'm not sure that does current sensing - I...
View ArticleMotor shield for R/C Omnibot
Hi Dirk - thanks very much for the quick reply. I was thinking the adafruit v2 shield was a follow-on from the Make v1.1 shield but it looks like I was mistaken! I think I got confused as they're both...
View ArticleAngular Clock bug at 56 minutes past the hour
Any update on this? Love the clock, but keen to fix this bug.
View Article